-40%
HappyModel CrazyF4 ELRS 915MHz AIO Flight Controller
HappyModel CrazyF4 ELRS 915MHz AIO Flight Controller
HappyModel CrazyF4 ELRS 915MHz AIO Flight Controller
HappyModel CrazyF4 ELRS 915MHz AIO Flight Controller
HappyModel CrazyF4 ELRS 915MHz AIO Flight Controller
HappyModel CrazyF4 ELRS 915MHz AIO Flight Controller

HappyModel CrazyF4 ELRS 915MHz AIO Flight Controller

$ 31.14

Availability: 100 in stock
  • Condition: New
  • Restocking Fee: No
  • Refund will be given as: Money back or replacement (buyer's choice)
  • Item must be returned within: 30 Days
  • All returns accepted: Returns Accepted
  • MPN: Does Not Apply
  • Brand: Genuine
  • Return shipping will be paid by: Buyer

    Description

    The World first AIO 5in1 whoop flight controller built-in Expresslrs receiver is coming out now. This F4 flight controller built-in 5A esc , VTX, OSD , high performance 915MHz expresslrs receiver, it’s best for 1S Long Range and Tinywhoop.
    Specifications:
    Flight controller
    MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
    Sensor: MPU-6000(SPI connection)
    Original whoop size compatible
    Power supply: 1S battery input (DC 2.9V-4.35V)
    Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
    Built-in Betaflight OSD(SPI Control)
    Built-in 5.8G VTX
    Built-in Serial-based ExpressLRS 900MHz receiver(915MHz or 868MHz optional)
    Built-in 5V 1A BEC
    Flight controller firmware target: CRAZYBEEF4DX
    Onboard 4in1 ESC
    MCU upgraded to EFM8BB21
    Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
    Support BLHeliSuite programmable
    Factory firmware: O_H_5_REV16_8.HEX
    Default protocol: DSHOT600
    Onboard Serial-based ELRS Receiver
    Operation current: ~100Ma
    Rx To FC protocol: CSRF
    RF Frequency optional: 915mhz or 868mhz(EU)
    Antenna connector:  IPEX4
    Telemetry output Power: <17dBmFirmware target: Happymodel_RX_ES915RX
    Receiver protocol: CRSF
    Could bind with Happymodel ES915TX , Frsky R9M and DIY ELRS TX module(need to flash the same version ELRS firmware)
    Firmware flash via Betaflight pass-through
    Onboard 5.8g VTX
    Output power: 25mw~200mw switchable
    Frequency: 40CH
    Input voltage: 3.3V 5.5V
    Current consumption: 300mA(type)
    Frequency: 5.8GHz 5bands 40 channels(include Race band)Smartaudio ready
    Onboard voltage and Amperage meters  settings
    Voltage meter scale setting 110
    Amperage meter scale setting 1175
    Bind procedure:
    Supply power to CrazyF4 ELRS flight controller (Plug the USB), wait until the RX LED is off, immediately turn off the power (Unplug the USB), and then repeat the above steps again. When the RX is powered on for the third time, the LED light will start to double-flash, which means that the RX enters into the binding mode
    Insert the ES915TX module or other DIY 2.4G ELRS TX to your OpenTX Radio transmitter, and choose External RF mode to CRSF protocol, then you can find ELRS menu from the Radio system (Need to copy the ELRS.LUA file to the SD-Card tools first), Enter into ELRS and press [Bind], the RX LED on the Flight controller will getting to be solid if bind successfully.
    Receiver LED status meanings:LED solid means bind successful or Connection established; LED double-flash means in bind mode; LED flash slowly means no signal established with the TX module
    Notes: Don’t make the antenna plug get touch with the Motor solder pins, otherwise it would burnt the ESC.